NEC
2010 Incorrect power-off Error
The 2010 incorrect power-off error is an error code that presents in some late Series 2 as well as NEC laser projectors. Quite simply put, this error presents when the projector did not go through a proper power off sequence, such as a power failure ...
(129) Down Lamp Power(Exhaust, xx.x, xx.x) and (17x) Errors
The above referenced error code occurs when the projection lamp is overheating in the projector. It usually indicates that the external exhaust fan is off, blocked or non-functional. This error will cause the projector to self protect and shut down. ...
NEC 900/1100 177 Tamper Fail Error
When the 177 Tamper Fail error message appears on an NEC NC-900c/1100 projector, it generally indicates that one of the door tamper switches has been tripped. When the error appears on the side LCD panel or in the Digital Cinema Communicator, it ...
NEC Series 2 Frame Rate Capability
IMB Comm Fail(000000:Conn=113)
When an NEC projector displays IMB Comm Fail(000000:Conn=113) message it means that the projector can no longer communicate with the IMB or IMS type server. It is normal for this message to appear when the IMB server is shutdown or rebooting. ...
125 LPSU Fail (No Lamp) Message
While there are a number of reasons that an NEC projector would exhibit an LPSU (Lamp Power Supply) message, there are two that are very common. The NC1200/2000c projectors feature an external circuit breaker that protects the LPSU. Although NEC ...
NEC S2 Projector Displaying 3xx Error
NEC errors in the 300 range generally pertain to an issue with the ICP board. The ICP board contains the projector's security certificate so this can be a fatal one. There are two batteries on the ICP board. One battery can be changed, the other ...
NEC Series 2 - 4xx error
This problem is caused by the TI Link Decryptor, better known as the Enigma board. When using a projector with a "traditional" type of server (as opposed to an IMB/IMS type server), the signal coming from the external server is encrypted and ...
NEC Cinema equipment extended Off - Supplement guidance sheet (ver1)
NEC Cinema equipment extended Off – Supplement guidance sheet Question: If the cinema equipment needs to shut down for an extended period, is there any concern with the IMS/Option card/PJ internal battery going bad, or discharging? To help clarify, ...
NEC Cinema equipment installations best practice guidance for extended Off times (ver1 3)
Guidance for protecting your NEC projection equipment when your theatre/post production installation might be closed for a while Due to the actual force majeure of closing cinema installations for an unknown period of time, we would like to provide ...
NEC Projectors - Preparation for a temporary Shutdown
For NC1200C, NC2000C, NC3200S, NC3240S, NC900C, NC1100L: If there is an Enigma card (PN# NC-80LB01) in these units, please make sure it is fully charged (48 hrs. of power On should be sufficient). The Enigma charge normally remains for about 6 month, ...
NEC Digital Cinema Replacement Air Filter Chart
The equivalent TCS filters are: NC-80AF01 - NECFILTER77 NC-80AF02 - NECFILTER3593 We also have a custom filter for the NEC projectors. The TCS NECFILTER795 replaces the 2 - NC-80AF02 filters on the front of the projector. Instead of 2 - 3.5" x 9.5" ...
Turning projector ON from STANDBY turns on lamp.
This is a common problem with NEC Series II projectors. The problem occurs when the projector has been shutdown with the lamp on or in lamp cooling mode. If the projector is placed into STANDBY mode before the lamp shutdown cycle completes, the ...
NEC S1 & S2 (Xenon) Air Filter Replacement Chart
Lamp replacement NEC NC Series digital projectors (Ushio video)
This video, provided by Ushio, describes the lamp replacement procedure on NEC series 2 projectors. NEC Cinema Xenon lamp Replacement Procedure (Ushio) FYI - Ushio lamps are available through Total Cinema Solutions.
Lamp replacement NEC NC Series digital projectors
This video, provided by Philips, describes the lamp installation procedure on NEC series 2 projectors. NEC Series 2 Lamp Installation Procedure FYI - Philips digital projection lamps are now sold under the Lighting Technologies International (LTI) ...
Lamp Alignment in NEC Digitial Cinema Projectors
This video, provided by Philips, describes the lamp alignment procedure on NEC series 2 projectors without using the NEC DCC software. NEC Series 2 Lamp Alignment Procedure FYI - Philips digital projection lamps are now sold under the Lighting ...